Upload date
All time
Last hour
Today
This week
This month
This year
Type
All
Video
Channel
Playlist
Movie
Duration
Short (< 4 minutes)
Medium (4-20 minutes)
Long (> 20 minutes)
Sort by
Relevance
Rating
View count
Features
HD
Subtitles/CC
Creative Commons
3D
Live
4K
360°
VR180
HDR
1,967 results
31.6K subscribers
In this video I go about making repairs on the electric motor on a circulating pump I bought for my shop hydronic system. This unit ...
6,307 views
2 weeks ago
In this video I resurfaced some duramax diesel gm cylinder heads. A real low feed rate with some wd40 did the milling followed by ...
4,903 views
2 months ago
In this video I fix up another almost 50 year old Deere Cylinder head. Keeping the vintage iron in the fields.
2,933 views
1 month ago
In this video I resurface a 4239 Deere cylinder head onstall new valves and grind the seats for ptoper sealing and heat transfer.
2,919 views
5 months ago
Area Diesel Service Inc has partnered up with Brian Block (bcbloc02) for the fuel injection portion of an engine swap on a vintage ...
30,242 views
5 years ago
Got a real mess to fix with this one! Nothing is flat parallel or concentric but it is all supposed to be so where to start? Follow along ...
36,547 views
How did they do that? A look at a 175year old door hinge and hopefully come up with a plan for its repair so it can serve another ...
2,724 views
10 years ago
In this video I hard mill some rock busting bits from some big hydraulic Ho rams it's a real hard time!
6,974 views
8 months ago
f you want to see more Doubleboost content & help support this channel , consider becoming a patrion ...
1,890 views
23 hours ago
1,951 views
20 hours ago
In this video I do the machine work to get the casting I welded up back to the original specifications. This obsolete Deere 555G ...
17,128 views
3 years ago
In this video I continue on with the final drive repair of the obsolete dozer casting. Follow a long as i do some complex cast iron ...
21,628 views
In this video I bore a worn and corrosion damaged Early John Deere A block .045” oversized to give it back a decent ring seal and ...
9,925 views
1 year ago
In this video I weld up and restore the bearing fit on a trashed PTO shaft. Nothing tricky, just some welding and turning. I hope you ...
13,227 views
In this video I get started on modifying an old rough head that will wind up on a much wilder application. Follow along for milling, ...
7,925 views
In this video I fix the holes in the old rusty crusty cylinder head that were cut in it in the process of extreme porting for some big ...
6,278 views
Thank you for watching! Shop for Surfacing Flycutters from Performance CBN and much more surfacing machine tools.
8,029 views
In this right to repair video I take on a major job rebuilding a Deere tractor swivel frame. This thing has lived a high stress life ...
16,438 views
In this video I talk about a misfire issue that developed with my 98 Dodge Dakota. I determined it seemed to be a lifter pumping up.
4,411 views
3 months ago
This job was ultra simple yet it turned into a big challenge. It turns out this part acted like a giant tuning fork. I had all kinds of ...
21,178 views
Checking out bcbloc02's impressive machine shop with a large Monarch lathe, Cincinnati horizontal mill and a Giddings & Lewis ...
36,646 views
9 years ago
In this video it was cold so I decided to see how the injectors I have been running would start in near 0F temps. It lit right off just ...
8,273 views
In this video I go about some challenging workholding only to run into another problem. Lack of swing for clearance. So what to do ...
18,622 views
7 years ago
In this video I talk about some calipers I recently purchased and how sometimes you can have faulty measuring tools and it be ...
13,539 views
4 years ago
HELP NEEDED!! The smoke has been let out of the motor on the Monster Monarch. It still ran fine but apparently had internal ...
12,327 views
Boring axle tubes out of an AAM 11.5 axle so lighter and shorter tubes can be installed for racing.
6,345 views
6 months ago
